K&D Factory Service Inc. bas been bringing OEM commercial cooking parts and service to restaurants and commercial kitchens of Dover, PA and the surrounding areas since 1945!
Read our reviews and find out why your colleagues consider us to be their nearby commercial cooking supply company in Dover, PA.
Local Reviews
for Dover, PA
Our Reviews by City
good job
Providence - Dover, PA 17315
Service C.
Checked hi limit on Gas Fryer, is good. Found a lot of carbon on limit. Cleaned off. Brought up to temp. Tested okay.
Service C.
Conveyor Oven not heating, checked voltages, 237.7 High Voltage, But only 22.4 volts on Low Voltage, recommend to replace Transformer and relay, had 22.4 at gas valve but would not pull in, transformer is weak, contact said to replace both transformers in upper and lower unit. 9/05/19 Top oven, Replaced old Fenway ignition module with the new updated Fenway module. Cleaned ignitor, checked at set gas pressure to 4.0 in WC. Checked both cooling fans, okay. Unit still comes up with error Open and 909F error. Temp control module face is melted and probe is no good. Kyle said replace both ASAP. Bottom over, replaced obsolete Honeywell ignition module with the new Fenwal updated module, running now and seems okay. Cleaned ignitor, checked gas pressure and set at 4.0 in WC. Checked the 24 volt, seems okay, left the transformer with manager. Per Kyle. Will return with new Temperature module and probe to replace.
Service C.
Delimed Combi Oven unit. Tested okay.
Service C.
Cleveland Steamer - Removed and replaced boiler based steamers. installation is not complete. Unit will be completed tomorrow. 4/3/19 Made final connections. Let heat up to temperature. found no leaks. tested kettles connected. found ready to use.
Service C.
Chef asked me to look at the coffee/juice machine in connections dining room. Needs a new water filter. Called United in York and ordered. Will be in Monday. 11/07/18 Picking up parts locally. Replaced water filter, all good.
Service C.
Kitchen chef requested a door gasket replacement for walk in cooler. Door make is thermalrite. s/n 188960. hinges on the right side. is 3 sided gasket. size= 37 3/4 in x 78 in part# 180 **mileage and travel on work order #160691** 10/05/18 Installed new door gasket **mileage and travel on work order #167164**
Service C.
Kitchen chef requested a door gasket replacement for walk in cooler, door make is thermalrite. s/n 188960. hinges on the right side. Is 3 sided gasket. size= 37 3/4 in x 78 in part# 180 **mileage and travel on work order #160691** 10/05/18 Installed new door gasket **mileage and travel on work order #167164**
Service C.
Installed pins, and racks on Rational Combi-oven per quote, Tested okay.
Service C.
Found temp control board not closing sometimes. Will order parts 1/31/18 Installed temp probe, temp board and potentiometer switch. Set temp, tested okay.
Service C.
Convection Oven motor very loud on startup, have 120v to motor, okay to order. 1/9/18 Installed motor, brought up to temp, tested okay.
Service C.
Delimed unit brought up to temp tested okAY. found steam gaskets bad and sc pump hose bad, will replace on other work order - Travel & Miles on work order 146987
Service C.
Took pictures of rust, fan shroud cover rusting, rear top left pin broke off, both inner racks rusting, 3 oven racks rusting, probe is broke, all pins rusty, will call Rational for more info on rusted unit 3/1/17 Removed top on unit to grind off and drill out 2 rear pins, installed pins then put back together, advised Customer that unit is rusting through at steam inlet, will not be long till it rusts through
Service C.
We found fan blade on exhaust fan did not fit new motor. Returned and installed motor and fan blade. Checked operation.
Service Check-In ..
FRYMASTER HOLDING CABINET Tech - Installed rear bezel 3rd down, tested unit working okay