Careers Call Now Contact Us

Dillsburg PA Commercial Refrigeration

K&D Factory Service Inc. bas been bringing OEM commercial cooking parts and service to restaurants and commercial kitchens of Dillsburg, PA and the surrounding areas since 1945!

Read our reviews and find out why your colleagues consider us to be their nearby commercial cooking supply company in Dillsburg, PA.

Local Reviews
for Dillsburg, PA

K&D Factory Service Inc. Rated 5.0 out of 5 stars based on 1 customer reviews
Mobile Tools for Contractors and Service Professionals Powered by Nearby Now


Map of Dillsburg, PA

Saved our bits




Review of K&D Factory Service Inc.

We had a major event coming up and the guys over at K&D did everything in their power to get us back up and running


Mark B.

Mark B.

Arrived at location on 7/15/22 - Let unit produce the batch of ice it was in middle of making. I then turned the unit off and removed all removable parts from water side of unit. Cleaned and sanitized parts. I then cleaned and sanitized the inside of the unit. I put the parts back into the unit and let the unit run its 30 minute clean cycle. After the clean cycle I turned the unit back on and let it produce a batch of ice and discarded the batch. I notice that the unit has a water filtration unit but it fell off of the wall because it mounts with 3m tape. There is no other way to mount the system and I wouldn’t trust taping it back up. We will need to quote for a new water filtration system that we can mount with bolts or screws to either the machine or the wall. Unit is now running properly except the filtration system is hanging off of the unit.

Near Logan Rd, Dillsburg, PA 17019
Mark B.

Mark B.

Arrived at location on 5/5/22 - kitchen was at 84 degrees. Compressor was encased in ice like it was getting liquid flood back. Went to air handler in attic and found unit running but A-Coil was encapsulated in ice. This was restricting airflow which was causing the flood back. Turned heat on to thaw out coil quicker. As it was draining I noticed that drain was backing up. Blew out with CO2 and it cleared some debris out. Once coil was defrosted I cycled unit on and monitored pressures and supply/return temperatures. Found that pressures were low for current ambient temperature. Used manufacturer psychometric chart and added 2lbs of 410A refrigerant. Performed leak test with electronic leak detector and could find none at air handler or condensor. It appeared some work was performed on it and I am uncertain that correct charge was placed in. Room began dropping in temp and it will take some time for it to reach setpoint. I spoke with Jessica about the current temp setting

Near Logan Rd, Dillsburg, PA 17019
Mark B.

Mark B.

Arrived at location on 3/9/22 - Found compressor to be grounded and customer would like compressor ordered and replaced , part is on order at United Harrisburg and available on 3/10/22. Returned to location on 3/15/22 - After removing old compressor I found base of condenser unit fell apart in pieces, base doubles as the condensate pan and if left like that unit will leak water and also compressor can not be secured, spoke with customer and he gave me the okay to order whole condenser unit and replace. Condenser unit is on order at United Harrisburg I spoke with John and he will let me know the availability of unit when he finds out. Returned to location on 3/22/22 - Replaced condenser unit, checked for leaks with nitrogen and found none, vacuumed which held for fifteen minutes. Recharged system with factory amount of 134A, waited for unit to come down to temperature and is working properly at this time.

Near S Baltimore St, Dillsburg, PA 17019
Mark B.

Mark B.

Arrived at location on 10/13/21 - While doing pm found high float probe wasn't allowing ice to make proper thickness of ice. Tried to adjust thickness probe and unit wouldn't recognize adjustment. Removed side over and tested probe magnet by moving magnet up and down probe. Found up or down unit wasn't turning off led light to recognize water level. Called supply house they had one in stock. Picked up new thickness probe and returned. Installed new probe and tested operation unit made ice with proper thickness achieved all ok.

Near Trinity Dr W, Dillsburg, PA 17019
Mark B.

Mark B.

Arrived at location on 8/2/21 - Replaced both thermometers on walk in cooler and freezer.

Near Tuckahoe Rd, Dillsburg, PA 17019
Libby D.

Libby D.

RANDELL PREP TABLE - 04/14/21- Tom-Found condenser motor bad and compressor too hot to touch, replaced motor from truck stock, unit ran for about 5 minutes then compressor got very hot and shut off, compressor is bad and will need replaced, customer would like a quote on repair. 04/16/21- Shawn- Picked up parts from supply house. Removed old compressor and drier. Installed new compressor and drier, vacuumed and weighed in charge. Top works fine but the base is not feeding right and pressure is low. Also evaporator drain pan is busted. (Manager wants base repairs quoted.)

Near US-15, Dillsburg, PA 17019
Service C.

Service C.

1-18-21 Adjusted TBC Oven striker and door hinges. found only pulling 9 amps on mag circuit. found left side wire came off of the diode, reconnected and found pulling 17 amps. cooked an egg and temped correctly. sys ops ok.

Near US-15, Dillsburg, PA 17019
Service C.

Service C.

Came in and per customer, the Oven unit was showing F4 error code. removed the top unit to work on the bottom. checked switch sequence and found the microswitch wasn't engaging. also found primary and secondary latch on the same time. found the monitor switch broke off. replaced monitor switch. also adjusted the primary switch. checked magnetron, circuit pulling 17 amps. let unit get to temp and had customer use. operation okay with no error codes showing up. I cleared all of the faults.

Near US-15, Dillsburg, PA 17019
Service C.

Service C.

Went on roof to fryer hood. Fan Belt was tearing and there was a spare belt there. Replaced customer supplied belt and unit now running.

Near US-15, Dillsburg, PA 17019
Service C.

Service C.

removed old frymaster fryer and installed new henny penny fryer. opened box and found that the doors were off and the computers were not installed properly and were ready to fall out. per Cory they just want us to fix because they needed fryers. repaired all doors and put computers back into place. while going to plug fryers in, found cords for the far right was not long enough. ran and got cords and installed longer cords. finished installing unit and set up computers. talked to Steve martin at henny penny about doors and computers and sent pictures. he told me that Taylor afs need to be called. tried to call but was on hold the whole time and no answer. advised customer to call them to do the startup. loaded old fryer onto trailer and will take back to the shop to get rid of.

Near US-15, Dillsburg, PA 17019
Service C.

Service C.

Fry Filtering Device units filter pump wasn't pumping oil. customer said they filtered two vats last night but not the third. It didn't when I checked. I tried to put flexible hose in to see if there is anything clogged inside the vat or oil drain. also possibility of having filter pan clogged especially when I turned filter without hooking drain pan. I can hear air been pumped to the vat. had customer clean drain pan and tried to filter other vats, left and middle since they were up to temp. they filter fine. waited for the right one to get up to temp and filtered it too. everything is working and pump is pumping oil, operation okay.

Near US-15, Dillsburg, PA 17019
Service C.

Service C.

per customer "prob" display (=temp probe) when turned on. No problems today. Oven Unit has been sitting idle all summer. Probe connections a little loose on board. Cleaned connections, could not duplicate problem. Could not remove kick plate screws, per Maint Man Joe, will deal with in the future.

Near S Baltimore St, Dillsburg, PA 17019
Service C.

Service C.

found steam coming out both Steamer door gaskets. Top condensate spray nozzle totally plugged and bottom partially plugged. Replaced top nozzle and reversed door gasket, tested okay. Will reschedule bottom compartment for Friday after breakfast. Tech will need one Cle145555 spray nozzle. 7-26-19 returned with nozzle. removed bottom condensate nozzle and flushed out the lines. installed new nozzle and checked operation to unit, found no steam coming out of the doors. all operation okay.

Near Tuckahoe Rd, Dillsburg, PA 17019
Service C.

Service C.

checked the unit and found Blender left slide motor making grounding noise every time the slide goes up or down. talked to mfg, talked with Rodger. he recommended to replace motor because it's going bad, will obtain part and return. I deactivated left side until we fix it. 6-12-19 returned with part. removed old liner actuator and installed new actuator and checked operation by blending with unit. found no noise in unit.

Near US-15, Dillsburg, PA 17019
Service C.

Service C.

checked out Electric Fryer unit and found that the pilot was burning orange and not hitting the thermocouple but pilot was on. also found cracks in burner box and burner need replaced along with the blower motor and wheel. due to the burner box damage oven not worth fixing.

Near Franklin St, Dillsburg, PA 17019
Service C.

Service C.

Verified customers concern, Walk-In Cooler running warm, Found box warm, Checked condenser unit and found no power to unit, Checked breaker and found it to be turned to off position not tripped, Switched breaker on and unit came on and is cooling, unit is working properly at this time.

Near Tuckahoe Rd, Dillsburg, PA 17019
Service C.

Service C.

Found Reach-In Freezer drain line froze up, Put unit into defrost and defrost coils are working and drain line heater has power going to it but not getting warm, Checked heater and is open reading, Unit will need a new drain line heater, Talked with Michael at Minus Forty tech support and part number for drain line heater is #1291, customer would like a quote on the completion of this. 3/7/19 Removed evap cover and drip tray. tried to pull old drain heater but could not. it''s stuck inside drain line. I opened other end of drain line. blew out with nitrogen but nothing. probably drain line is iced up. I poured hot water little by little still could not pull drain heater. manager decided to let unit sit overnight and we will come back tomorrow. I left all parts of unit unscrewed. screws are in plastic bag.

Near Trinity Dr W, Dillsburg, PA 17019
Service C.

Service C.

Checked out unit & found working on arrival. After running for awhile, found front probe in red and showing shorted and temp not coming up. Customer too busy to look at. Will set up for Wednesday morning. 5/16/18 hecked out unit & found that cable was pinched on board. Installed new board & cable on right side. While checking, found low AMP reading on front element. Found voltage reading 104 volts. Moved cords around & got 209 back. Will quote repairs. Closing out per Ted

Near U.S. Hwy 15/501, Dillsburg, PA 17019
Service C.

Service C.

disconnected and removed old ice machine. Set new one in place and connected plumbing and electric. Unit is making ice.

Near Trinity Dr W, Dillsburg, PA 17019
Service C.

Service C.

Checked out unit & found continuity through neutral wire to plug. Installed new plug end & checked operation, okay. Also found that drive chain needs shortened & idler sprocket is hitting roller sprocket. Will obtain parts & return. 8-31-17 Did replace the idler sprocket, spring, sprocket & chain. I did free the idler bushing with emery cloth & grease. Reinstalled & checked operation, okay & ready to use.

Near US-15, Dillsburg, PA 17019
Service C.

Service C.

Checked out unit & found interlock switch bad along with door latch. Will obtain parts & return. 05/22/17 Returned with parts. Removed and replaced door latch and interlock switch. Checked operation okay

Near US-15, Dillsburg, PA 17019
Service C.

Service C.

Checked unit. Customer installed blade & insured me that they cleaned hub before installing. Blade has a wobble. Also old one wobbled. I will order a new hub bearing assembly & knife. 05/22/17- Returned with part. Removed old hub and installed new. Installed customer supplied knife. Checked operation okay. Also adjusted sharpeners

Near US-15, Dillsburg, PA 17019
Service C.

Service C.

Checked unit & found door gasket missing. Turned on & found wash tank high limit tripped. I reset & the wash thermostat overheated tank. I will order gasket & thermostat. 11/30-/16 Returned with parts. Removed old thermostat and installed new thermostat. Also installed door gasket on top. Set wash temp to 156 and checked operation okay

Near Trinity Dr W, Dillsburg, PA 17019
Service C.

Service C.

Per customer no problems today and unit (GAR Clamshell) working. Complaint was unit would not get down for breakfast. Advised if happens again is "button beeping"

Near US-15, Dillsburg, PA 17019
Service Check-In ..

Service Check-In ..

Globe Slicer Tech - Checked over unit and found it needs the following parts: Chain roller (cam follower) 1097; sharpening stones 240030,240031; front switch overlay 1159; table knob 407AS. Sharpener assembly sticks but moves. Advised customer on how to put the oil in

Near US-15, Dillsburg, PA 17019

Planned Maintenance

A planned maintenance agreement can keep your equipment running longer than the factory warranty. Reduce cost, downtime and have your equipment running at top performance when you need it most.

We Do It Right The 1st Time!

See what our customers think about our service!

Great service Very courteous polite and knowledgeable The Gardens At Stroud Stroudsburg
Super Guys! The K & D Team of repairman are super!. always courteous, friendly and get the job done right! Answer my questions and never a surprise cost. Dunmore Health Care Center Dunmore
Maintenance Supervisor Shawn is a good Devoted Service Tech from your Altoona Offfice Steve Long is always a great help when i call him Mount Union School District Mount Union
Read More